5732 - MachXO2: Is there a way to determine the status of the JTAGENB pin from within the device using RTL?

There is no way to detect the JTAGENB using verilog/VHDL, this function acts as a switch to enable and disable the state of JTAG.
In the Primitives List in the help options, the JTAGF - a primitive, is used to provide access to internal JTAG signals from within the FPGA fabric. It is the closest command code that can be used to access JTAG in the fabric.

Related Articles
534 - MachXO: Why can't I scan or program the MachXO device on the MachXO Mini board after I programmed my pattern into the device?
The MachXO JTAG pins on the MACHXO Mini board share the same traces with some generic IOs of the MachXO device (as shown on page 4 and page 2 of the schematic). If the new design patterns have signals driving out of these pins, they could potentially ...
1943 - MachXO: With no DONE bit, how can I use JTAG to see if the SRAM download from flash is finished?
The way to check the MachXO configuration status through JTAG is to use the capture instruction. For the MachXO the capture instruction (which is the instruction shifting out of the instruction register) is 0x19 (if the device is blank) or 0x1D (if ...
2155 - MachXO2/MachXO3: How can you determine if the MachXO2 has booted from the internal flash or SPI flash using dual boot?
Solution: You can read the Flash and SRAM Status Register using ispVM or Diamond Programmer. Here are the steps to follow: 1)) Device powers up check the DONE SRAM Status Register (1=Device booted successfully, 0=Device did not boot successfully) 2) ...
2043 - LatticeXP2: Can the CSSPIN pin be used as a GPIO in dual-boot mode on the LatticeXP2 device?
Description: When using the LatticeXP2 device in dual boot mode, the FPGA continuously drives the CSSPIN high. The CSSPIN is considered a dual-purpose pin. However while the CFG0 pin = 0, controlling the dual-boot function, it will cause CSSPIN to be ...
6460 - LatticeECP2/M: "ERROR - Failed in Function VERIFY_STATUS (see log file for more details)" - possible issue when trying to configure an FPGA using HW-USBN-2B?
Description:Error message: ERROR -Failed in Function VERIFY_STATUS (see log file for more details) Solution:It is possible that the issue came from a microcontroller connected to the FPGA's PROGRAMN pin. This pin is intended to hold off the FPGA ...

5732 - MachXO2: Is there a way to determine the status of the JTAGENB pin from within the device using RTL?

5732 - MachXO2: Is there a way to determine the status of the JTAGENB pin from within the device using RTL?

Related Articles

534 - MachXO: Why can't I scan or program the MachXO device on the MachXO Mini board after I programmed my pattern into the device?

1943 - MachXO: With no DONE bit, how can I use JTAG to see if the SRAM download from flash is finished?

2155 - MachXO2/MachXO3: How can you determine if the MachXO2 has booted from&nbsp;the internal flash or SPI flash using dual boot?

2043 - LatticeXP2: Can the CSSPIN pin be used as a GPIO in dual-boot mode on the LatticeXP2 device?

6460 - LatticeECP2/M: "ERROR - Failed in Function VERIFY_STATUS (see log file for more details)" - possible issue when trying to configure an FPGA using HW-USBN-2B?

2155 - MachXO2/MachXO3: How can you determine if the MachXO2 has booted from the internal flash or SPI flash using dual boot?