380 - ispLEVER Classic/Diamond Reveal Analyzer: using a JTAG chain with multiple devices

Reveal Logic Analyzer can be used for On-Chip Debug even if the targeted device is a JTAG chain with multiple devices.

Use ispVM to define the JTAG chain and the position of the targeted device in the chain. Then, save the chain (.xcf) file and upload the .xcf file into the Reveal Logic Analyzer during project creation.

Some limitations apply.

Users can only debug one device at a time in a daisy chain.;
Only one of the bitstreams in a daisy chain can include a Reveal core.

For detailed information on the Reveal Logic Analyzer, go to the ispLEVER Help menu or the Lattice Diamond Help menu. This contains the Reveal Tutorial and the Reveal User Guide which detail how to create the Reveal core and set up the Reveal Logic Analyzer.

Related Articles
Lattice Diamond Programmer: Do JTAG Full VME embedded source files are supporting JTAG Daisy Chain Programming?
The answer is yes, JTAG Full VME embedded source files are supporting the JTAG Daisy Chain Programming. The chain of devices setup should be done in the Lattice Diamond Programmer file (.xcf) by adding target device/s.
5075 - How to use Reveal with Soft JTAG for debugging the design?
See the following example from the CrossLink/LIFMD device family, which does not provide a hard JTAG block. Therefore, Reveal JTAG support is implemented using Soft JTAG debugger logic and GPIO pins will be used for four JTAG pins (JTAG_TCK, ...
7461 - ispLever Classic 2.1: Why is the "PULL" option of ispLever Classic not editable for designs using ispMACH 4000V/B/C/Z device?
When creating a design in ispLever Classic using ispMACH 4000V/B/C/Z devices, the "PULL" constraint option cannot be edited individually for each I/O and is greyed out. For the ispMACH 4000V/B/C/Z devices, the "PULL" constraint can only be edited on ...
Lattice Radiant and Diamond: How do i resolve core0 error when Running reveal analyzer? How to resolve Error "Core0 incorrect pattern readout" while running Reveal Analyzer?
Description: When running the reveal analyzer a "Core0 incorrect pattern readout" error is encountered causing the tool to not generate its desired waveforms. Solution: This can be resolved by making sure that you have the following: 1) JTAG TCK is ...
Diamond version 3.13 Reveal Analyzer fails when using a HW-USBN-2A cable on a machine with an Intel CPU: ERROR - failed to set cable port (cable:USB port:EzUSB-0 error:-1).
Description: In Diamond version 3.13, when using a HW-USBN-2A cable on a machine with an Intel CPU, Reveal Analyzer may fail with the following error: ERROR - failed to set cable port (cable:USB port:EzUSB-0 error:-1). Solution: There is no planned ...

380 - ispLEVER Classic/Diamond Reveal Analyzer: using a JTAG chain with multiple devices

380 - ispLEVER Classic/Diamond Reveal Analyzer: using a JTAG chain with multiple devices

Related Articles

Lattice Diamond Programmer: Do JTAG Full VME embedded source files are supporting JTAG Daisy Chain Programming?

5075 - How to use Reveal with Soft JTAG for debugging the design?

7461 - ispLever Classic 2.1: Why is the "PULL" option of ispLever Classic not editable for designs using ispMACH 4000V/B/C/Z device?

Lattice Radiant and Diamond: How do i resolve core0 error when Running reveal analyzer? How to resolve Error "Core0 incorrect pattern readout" while running Reveal Analyzer?

Diamond version 3.13 Reveal Analyzer fails when using a HW-USBN-2A cable on a machine with an Intel CPU: ERROR - failed to set cable port (cable:USB port:EzUSB-0 error:-1).